Hello Janne!

25 Oct 2018 10:06, Janne Johansson wrote to Benny Pedersen:

 JJ> On 2018-10-25 00:40, Benny Pedersen : Michiel van der Vlist wrote:
 >> -áMvdV> and up).-á If the destination address is a 6to4 tunnel address
 >> -áMvdV> (2002::/16) many OSs default to IPv4 if an IPv4 address is 
 >> -áMvdV> present.
 >>
 >> time to update to a later glibc where ipv6 is prefered over ipv4 
 >> failback

 JJ> I think its mostly a setting in your resolv.conf or similar file to
 JJ> change default priority of v4 or v6 and not so much a age-of-glibc 
 JJ> issue.

   ----- gai.conf begins -----
# Configuration for getaddrinfo(3).
#
# So far only configuration for the destination address sorting is needed.
# RFC 3484 governs the sorting.  But the RFC also says that system
# administrators should be able to overwrite the defaults.  This can be
# achieved here.
#
# All lines have an initial identifier specifying the option followed by
# up to two values.  Information specified in this file replaces the
# default information.  Complete absence of data of one kind causes the
# appropriate default information to be used.  The supported commands include:
#
# reload  
#    If set to yes, each getaddrinfo(3) call will check whether this file
#    changed and if necessary reload.  This option should not really be
#    used.  There are possible runtime problems.  The default is no.
#
# label      
#    Add another rule to the RFC 3484 label table.  See section 2.1 in
#    RFC 3484.  The default is:
#
#label ::1/128       0
#label ::/0          1
#label 2002::/16     2
#label ::/96         3
#label ::ffff:0:0/96 4
#label fec0::/10     5
#label fc00::/7      6
#label 2001:0::/32   7
#
#    This default differs from the tables given in RFC 3484 by handling
#    (now obsolete) site-local IPv6 addresses and Unique Local Addresses.
#    The reason for this difference is that these addresses are never
#    NATed while IPv4 site-local addresses most probably are.  Given
#    the precedence of IPv6 over IPv4 (see below) on machines having only
#    site-local IPv4 and IPv6 addresses a lookup for a global address would
#    see the IPv6 be preferred.  The result is a long delay because the
#    site-local IPv6 addresses cannot be used while the IPv4 address is
#    (at least for the foreseeable future) NATed.  We also treat Teredo
#    tunnels special.
#
# precedence     
#    Add another rule to the RFC 3484 precedence table.  See section 2.1
#    and 10.3 in RFC 3484.  The default is:
#
#precedence  ::1/128       50
#precedence  ::/0          40
#precedence  2002::/16     30
#precedence ::/96          20
#precedence ::ffff:0:0/96  10
#
#    For sites which prefer IPv4 connections change the last line to
#
#precedence ::ffff:0:0/96  100

#
# scopev4    
#    Add another rule to the RFC 6724 scope table for IPv4 addresses.
#    By default the scope IDs described in section 3.2 in RFC 6724 are
#    used.  Changing these defaults should hardly ever be necessary.
#    The defaults are equivalent to:
#
#scopev4 ::ffff:169.254.0.0/112  2
#scopev4 ::ffff:127.0.0.0/104    2
#scopev4 ::ffff:0.0.0.0/96       14
   ----- gai.conf ends -----

speeks for it self, if unchanged config, ipv6 is prefered


 Regards Benny

... there can only be one way of life, and it works :)

--- Msged/LNX 6.1.2 (Linux/4.14.65-gentoo (x86_64))