Hi Patrick,
 
   I've got a 288i and am using the 1.440-12 ROM code (flasher worked fine).  
I run a single line BBS using D'Bridge front-end mailer, since the 1.440-XX 
flashers I've experienced a strange problem with my SupraFaxModem and DB, on 
a somewhat regular basis now (at least daily) incoming calls will not 
register a connect speed I'll just get CONNECT"  and nothing else.  At first 
I thought it may have been a 300 baud caller, but I had someone with a 28.8 
and 14.4 try it with the same results.  Just today the modem would only 
report NO CARRIER msgs until I reset the computer (this had gone on for 4 
hours while I was at work) once reset it worked fine.  Here are my settings:
Flashed:  29 Jun 96
 
ati3
V1.440-12-V34_DP
SupraFAXModem 288i
Built: June 25 1996 13:58:08
 
OK
ati7
RC288DPi Rev 04BC
 
OK
ati10
101,104,115,120,121,123,140,141,142,143,144,146,147,149,150,151,
153,154,156,157,180,181,186,190
SupraFAXModem 288i
 
101=Class 1 FAX           104=Class 2 FAX           115=V.17 14.4Kbps FAX
120=World Wide support    121=V.23                  123=Blacklisting
140=V.32bis 14.4Kbps data 141=SilentAnswer          142=CallerID
143=MNP10                 144=MNP10/Cellular        146=AT\S config display
147=V.FC 28.8Kbps data    149=V.FC 24.0Kbps data    150=Enhanced &F options
151=Enhanced rate control 153=V.34 28.8Kbps data    154=SilentAnswer Plus
156=Distinctive Ring      157=RINGING response code 180=16550 UART
181=SupraSMART UART       186=V.80 Sync Access Mode 190=FLASH memory
 
OK
AT M0 W2 S95=003 &W &W1 
 
OK
at&v
 
ACTIVE PROFILE:
B1 E1 L2 M0 N1 Q0 T V1 W2 X4 Y0 %C3 %E0 %G1 -K0 &C1 &D2 &K3 &Q5 &R1 &S0 &X0 
&Y0
S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:050 S08:002 
S09:012
S10:014 S11:095 S12:050 S18:000 S23:054 S25:005 S26:001 S36:007 S37:000 
S38:005
S40:104 S41:131 S44:131 S46:138 S48:007 S91:010 S95:003 S109:062 S110:014 
 
STORED PROFILE 0:
B1 E1 L2 M0 N1 Q0 T V1 W2 X4 Y0 %C3 %E0 %G1 -K0 &C1 &D2 &K3 &Q5 &R1 &S0 &X0 
S00:000 S02:043 S06:002 S07:050 S08:002 S09:012 S10:014 S11:095 S12:050 
S18:000
S23:054 S25:005 S26:001 S36:007 S37:000 S40:104 S41:131 S46:138 S95:003 
 
STORED PROFILE 1:
B1 E1 L2 M0 N1 Q0 T V1 W2 X4 Y0 %C3 %E0 %G1 -K0 &C1 &D2 &K3 &Q5 &R1 &S0 &X0 
S00:000 S02:043 S06:002 S07:050 S08:002 S09:012 S10:014 S11:095 S12:050 
S18:000
S23:054 S25:005 S26:001 S36:007 S37:000 S40:104 S41:131 S46:138 S95:003 
 
TELEPHONE NUMBERS:
0=                                    1=
2=                                    3=
 
OK
 
Any ideas why it would fall back to either just the NO CARRIER statement or 
the CONNECT without a speed associated with it?  It is extremely frustrating 
as it is costing me callers.  Now I have ordered my factory upgrade on my 
288i and understand it will be shipped on the 10th, but I'd still like to 
solve this problem.  Any help would  be appreciated.
 
Dale, Sysop
The SPECTRUM BBS
Fargo, ND
(701) 280-2343 
--- DB A3000sl/005017
---------------