| TIP: Click on subject to list as thread! | ANSI |
| echo: | |
|---|---|
| to: | |
| from: | |
| date: | |
| subject: | Courier Help Screens, April 29. |
Hi Rod,
You might want to save this to a text file (or whatever). It's the on-line
help screens from the latest SDL, and most of the available commands and
registers are now listed with much more detail than before. There also
appear to be quite a few sneaky little undocumented commands salted away
for a rainy day (the A> could be quite useful, for instance).
-------------------------------------------------------------------
HELP, Command Quick Reference
#$ HELP, Octothorpe Commands Kn n=0 Call Duration Mode
&$ HELP, Ampersand Commands n=1 Real Time Clock Mode
%$ HELP, Percent Commands Mn n=0 Speaker Off
A/ Repeat Last Command n=1 Speaker On Until CD
A> Continuously Repeat Command n=2 Speaker Always On
AT Command Mode Prefix n=3 Speaker Off During Dial
A Answer Call On n=0 Return Online
Bn n=0 V.32 originate mode n=1 Return Online & Retrain
n=1 HST originate mode n=2 Return Online & Speed Shift
Cn n=0 Transmitter Off P Pulse Dial
n=1 Transmitter On Qn n=0 Result Codes Sent
Dn Dial a Telephone Number n=1 Quiet (No Result Codes)
n=0..9#*TPR,;"W{at}!()- n=2 Verbose/Quiet On Answer
DL Dial Last Phone Number Sr=n Sets Register "r" to
"n"
DSn Dial Stored Phone Number Sr? Query Register "r"
D$ HELP, Dial Commands S$ HELP, S Registers
En n=0 No Command Echo T Tone Dial
n=1 Echo Command Chars Vn n=0 Numeric Responses
Fn n=0 Online Echo n=1 Verbal Responses
n=1 No Online Echo Xn n=0 Basic Result Codes
Hn n=0 On Hook (Hang Up) n=1 Extended Result Codes
n=1 Off Hook n=2-7 Advanced Result Codes
In n=0 Product Code Z Software Reset
n=1 Checksum +++ Escape Code
n=2 RAM Test $ HELP, Command Summary
n=3 Banner/Clock set
n=4 Current Settings
n=5 NVRAM Settings
n=6 Link Diagnostics
n=7 Product Configuration
n=10 Dial Security Status
n=11 Extended Link Screen
n=15 CID Status
HELP, Dial Commands
0-9 Digits to Dial
* Auxiliary Tone Dial Digit
# Auxiliary Tone Dial Digit
T Tone Dialing
P Pulse Dialing
R Call an Originate Only Modem
, Pause (Wait for S8 Time)
; Remain in Command Mode After Dialing
" Used to Dial Alpha Phone #'s
W Wait for 2nd Dial Tone (X3-X7)
{at} Wait for an Answer (X3-X7)
! Flash Switch Hook
HELP, Octothorpe Commands
#CID=n Caller ID control
n=0 Disable detection
n=1 Formatted results
n=2 Unformatted results
n=3 Formatted without name
n=4 Disable results to DTE
#CID? Show current setting
#CID=? Show supported settings
HELP, Percent Commands
%An= Security Account Information %Fn Remote DTE Data Format
Command Structure n=0 8, No parity
%An=PW,ACCT E,DIAL B,NEW#,PH# n=1 7, Mark parity
n = (0-9) n=2 7, Odd parity
PW = Password n=3 7, Even parity
ACCT E = Account Enable %L=PWn Security Local Access Psw
DIAL B = Dial Back Enable PWn = (0-9)
NEW# = New Dial Back # %Nn V.25bis Synchronous Clock Rate
PH# = Dial Back Phone # n=0 RESERVED
%Bn Remote DTE Data Rate n=1 RESERVED
n=0 110 bps n=2 1200 bps
n=1 300 bps n=3 2400 bps
n=2 600 bps n=4 4800 bps
n=3 1200 bps n=5 7200 bps
n=4 2400 bps n=6 9600 bps
n=5 4800 bps n=7 12000 bps
n=6 9600 bps n=8 14400 bps
n=7 19200 bps n=9 16800 bps
n=8 38400 bps n=10 19200 bps
n=9 57600 bps %Pn=s Store Remote Access Pswd
n=10 115200 bps n=0 Query Access Only
%Cn n=0 Defer Configuration n=1 Full Configuration
n=1 Revert Configuration %Pn? Query Remote Access Pswd
n=2 Execute Configuration n=0 Query Access Only
%E=n Erase Account Information n=1 Full Configuration
n=1 Erase Local Access Psw %S= Psw To Grant Local Access
n=2 Erase Autopass Psw %T Touch Tone recognition
n=3 Erase Accounts Psw %V=PWn Security Autopass Psw
n=4 Erase Accounts Phone # PWn = (0-9)
n=5 Erase Accounts Status
HELP, Ampersand Commands
&An n=0 Disable /ARQ Result Codes &Pn n=0 N.American Pulse Dial
n=1 Enable /ARQ Result Codes n=1 UK Pulse Dial
n=2 Enable /Modulation Codes &Rn n=0 CTS Follows RTS
n=3 Enable /Extra Result Codes n=1 Ignore RTS
&Bn n=0 Floating DTE Speed n=2 RX to DTE/RTS high
n=1 Fixed DTE Speed &Sn n=0 DSR Always On
n=2 DTE Speed Fixed When ARQ n=1 Modem Controls DSR
&Cn n=0 CD Always On n=2 Pulse DSR, CTS=CD
n=1 Modem Controls CD n=3 Pulse DSR
&Dn n=0 Ignore DTR n=4 DSR = DCD
n=1 On-Line Command Mode n=5 Modem Controls DSR, CTS=CD
n=2 DTE Controls DTR &Tn n=0 End Test
&Fn n=0 Load Factory Configuration n=1 Analog Loopback (ALB)
n=1 Hardware Flow Control Cnfg. n=3 Digital Loopback (DLB)
n=2 Software Flow Control Cnfg. n=4 Grant Remote DLB
&Gn n=0 No Guard Tone n=5 Deny Remote DLB
n=1 550 Hz Guard Tone n=6 Remote Digital Loopback
n=2 1800 Hz Guard Tone n=7 Remote DLB With Self Test
&Hn n=0 Disable TX Flow Control n=8 ALB With Self Test
n=1 CTS &W Store Configuration
n=2 Xon/Xoff &Xn n=0 DCE Synchronous Clock
n=3 CTS and Xon/Xoff n=1 DTE Synchronous Clock
&In n=0 Disable RX Flow Control n=2 RX Clock is Source
n=1 Xon/Xoff &Yn n=0 Destructive
n=2 Xon/Xoff Chars Filtered n=1 Destructive/Expedited
n=3 HP Enq/Ack Host Mode n=2 Nondest./Expedited
n=4 HP Enq/Ack Terminal Mode n=3 Nondest./Unexpedited
n=5 Xon/Xoff for non-ARQ Mode &Zn=s Store Phone Number
&Kn n=0 Disable Data Compression &Zn=L Store Last Phone Number
n=1 Auto Data Compression &Zn? Query Phone Number
n=2 Enable Data Compression &ZC=s Store Command
n=3 Selective Data Compression
&Ln n=0 Disable Leased Line
n=1 Enable Leased Line
&Mn n=0 Normal Mode
n=1 Synchronous Mode
n=4 ARQ/Normal Mode
n=5 ARQ Mode
n=6 V.25bis
n=7 V.25bis HDLC
&Nn n=0 Highest Link Speed
n=1 300 bps
n=2 1200 bps
n=3 2400 bps
n=4 4800 bps
n=5 7200 bps
n=6 9600 bps
n=7 12000 bps
n=8 14400 bps
n=9 16800 bps
n=10 19200 bps
n=11 21600 bps
n=12 24000 bps
n=13 26400 bps
n=14 28800 bps
n=15 31200 bps
n=16 33600 bps
HELP, S Register Functions
S0 Ring to Answer On S36 Reserved
S1 Counts # of Rings S37 Reserved
S2 Escape Code Char S38 Disconnect Wait Time (sec)
S3 Carriage Return Char S39 Reserved
S4 Line Feed Char S40 Reserved
S5 Backspace Char S41 # of Allowed Login Attempts
S6 Wait Time/Dial Tone (sec) S42 Remote Escape Code Char
S7 Wait Time/Carrier (sec) S43 Remote Escape Code Time (1/50sec)
S8 Comma Time (sec) S44 Leased Line Delay Timer (sec)
S9 Carrier Detect Time (1/10sec) S51 Bit Mapped
S10 Carrier Loss Time (1/10sec) 1 = MNP/V.42 Disabled in V.22
S11 Dial Tone Spacing (msec) 2 = MNP/V.42 Disabled in V.22bis
S12 Escape Code Time (1/50sec) 4 = MNP/V.42 Disabled in V.32
S13 Bit Mapped 8 = Reserved
1 = Reset On DTR Loss 16 = Reserved
2 = Do Originate in Auto Answer 32 = Reserved
4 = No Pause Before Result Codes 64 = Disable Selective Reject
8 = Do DS0 On DTR 128 = Enable phone exclusion delay
16 = Do DS0 On Reset S53 Bit Mapped
32 = Disable HST 1 = Enable Dial Security
64 = Disable MNP Level 3 2 = Enable Autopass Fallback
128 = Hardware Reset 4 = Enable Local Access Psw
S14 Bit Mapped 8 = Reserved
1 = Escape Code Hang Up 16 = Reserved
S15 Bit Mapped 32 = Reserved
1 = Disable High-Freq EQ 64 = Reserved
2 = Disable Online Fallback 128 = Reserved
4 = Disable 450 bps Back Channel S54 Bit Mapped
8 = Reduced Non-ARQ TX Buffer 1 = Disable 2400 symbol rate
16 = Disable MNP Level 4 2 = Disable 2743 symbol rate
32 = Set DEL=Backspace 4 = Disable 2800 symbol rate
64 = Unusual MNP-Incompatibility 8 = Disable 3000 symbol rate
128 = Custom Applications 16 = Disable 3200 symbol rate
S16 Test Modes 32 = Disable 3429 symbol rate
1 = Analog Loopback 64 = Disable V.8 Call Indicate
2 = Dial Test 128 = Disable V.8 Mode
4 = Test Pattern S55 Bit Mapped
8 = Remote Digital Loopback 1 = Disable 8S-2D trellis code
16 = Reserved 2 = Disable 16S-4D trellis code
32 = Reserved 4 = Disable 32S-2D trellis code
64 = Reserved 8 = Disable 64S-4D trellis code
128 = Reserved 16 = Reserved
S17 Reserved 32 = Reserved
S18 &Tn Test Timeout (sec) 64 = Reserved
S19 Inactivity Timeout (min) 128 = Enable phase roll detection
S20 Reserved S56 Bit Mapped
S21 Break Length (1/100sec) 1 = Disable nonlinear coding
S22 Xon Char 2 = Disable TX level deviation
S23 Xoff Char 4 = Disable preemphasis
S24 DSR Pulse Time (1/50sec) 8 = Disable precoding
S25 DTR Recognition Time (1/100sec) 16 = Disable shaping
S26 RTS/CTS Delay Time (1/100sec) 32 = Disable V34+
S27 Bit Mapped 64 = Disable V34
1 = V21 Mode 128 = Disable VFC
2 = Disable TCM S57 Reserved
4 = Disable V32 S69 Bit Mapped
8 = Disable 2100hz 1 = Disable Extrn. PnP
16 = Disable MNP Handshake 2 = Enable Auto Redial
32 = Disable V.42 4 = Reserved
48 = Disable V.42 Detect Phase 8 = Reserved
64 = Reserved 16 = Reserved
128 = Unusual SW-Incompatibility 32 = Reserved
S28 V32 Handshake Time (1/10sec) 64 = Reserved
S29 V21 Handshake Time (1/10sec) 128 = Reserved
S30 Reserved S70 Bit Mapped
S31 Reserved 1 = Enable ring type A
S32 Talk/Data Switch 2 = Enable ring type B
0 = Disabled 4 = Enable ring type C
1 = Originate Mode 8 = Enable ring type D
2 = Answer Mode 16 = Reserved
3 = Redial Last Number 32 = Reserved
4 = Dial Stored Number 0 64 = Reserved
5 = Auto Answer Toggle 128 = Reserved
6 = Reset Modem
7 = Initiate RDL
8 = Busy Toggle
9 = Execute Stored Cmd
S33 Reserved
S34 Bit Mapped
1 = Disable V32bis
2 = Disable Enhanced V32 mode
4 = Disable Quick V32 retrain
8 = Enable V23 Fallback
16 = Change MR to DSR
32 = Enable MI/MIC
64 = Disable RA Busy Msg
128 = Disable Terbo
S35 Reserved
------------------------------------------------------
Regards, Bill
@EOT:
--- MsgedSQ/2 3.30
* Origin: Logan City, SEQ (3:640/305.9)SEEN-BY: 640/305 711/934 @PATH: 711/934 |
|
| SOURCE: echomail via fidonet.ozzmosis.com | |
Email questions or comments to sysop@ipingthereforeiam.com
All parts of this website painstakingly hand-crafted in the U.S.A.!
IPTIA BBS/MUD/Terminal/Game Server List, © 2025 IPTIA Consulting™.