| TIP: Click on subject to list as thread! | ANSI |
| echo: | |
|---|---|
| to: | |
| from: | |
| date: | |
| subject: | M34F command set |
Hi Rod,
Dunno if I sent this to you earlier (I know I meant to, but have forgotten
whether I actually did or not), so here it is again. Might be useful to
know the M34F command set, in order to help Paul solve his many problems...
-----------------------------------------------------------------------
OK
at?
**** Interactive Command Help ****
AT? Lists entire help file
AT?cmd Gives help on the specified command string
AT?keyword Lists all commands and s registers that mention that keyword
+++ Escape Sequence **** Force Remote Access A/ Repeat Command
AT Commands ( * indicates default)
A Answer Incoming call
B Set Modulation Standard and Autorange (see tables)
! Lock Line Speed (disable fallback) eg ATB13!
D Dial Command, followed by phone number with optional Dial Modifiers
E Command Echo
= 0 Off
= 1*On
F Set Modulation Standard (for Automodem Emulation only)
H Hang Up
= 0 Disconnect and go on hook
= 1 Go off hook
= 2 Go off hook after current connection ends
I Firmware Identity
= 0 Numeric Firmware ID
= 1 Display Firmware checksum
= 2 Verify Firmware checksum (OK/ERROR)
= 3 Model ID
= 4 Revision & Creation Date
= 5 Manufacturer ID
= 8,9 Verbal Firmware ID
= 10 Modem Statistics
L Loudspeaker Volume
= 0 Lowest
= 1 Low
= 2*Moderate
= 3 Highest
M Monitor Speaker
= 0 Off always
= 1*On until connection
= 2 On always
= 3 On until connection, Off while dialling
= 4 On until connection, On during retrain and V32bis rate change
O On-line State
= 0 Go on-line
= 1 Go on-line & retrain (V32 & V22b only)
= 2 Retrain, don't go on-line (V32 & V22b only)
= 3 - 7 Rate change 4800 - 14400 (V32bis)
= 3 - 13 Rate change 4800 - 28800 (VFC or V34)
= 14 - 24 Retrain & change to 4800 - 28800 (VFC or V34)
P Set Pulse dialling
Q Quiet Mode
= 0*Off
= 1 On No responses (except to &v) given
= 2 No RING message and no CONNECT or NO CARRIER in answer mode
R Host interface speed selection
= 0* Autobaud speed detection enabled
= 2 2400bps
= 4 4800bps
= 7 7200bps
= 9 9600bps
= 12 12000bps
= 14 14400bps
= 16 16800bps
= 19 19200bps
= 21 21600bps
= 24 24000bps
= 26 26400bps
= 28 28800bps
= 38 38400bps
= 57 57600bps
= 76 76800bps
= 96 96000bps
= 115 115200bps
S Select S Reg n
= Sn? Read S Reg n
= Sn=x Set S Reg n with x
T * Set Tone dialling
V Response Codes
= 0 Numeric
= 1*Verbal
W Connect speed information
= 0 Use DTE speed for connect message
= 1 Use DTE speed for connect message
= 2*Use DCE speed for connect message
X Extended Response Codes
= 0 Codes 0-4,8 OK,CONNECT,RING,NO CARRIER,ERROR,NO ANSWER
= 1 as X0 +codes 5,10-12,30-40,60-62 CONNECT speed
= 2 as X1 +code 6 NO DIALTONE
= 3 as X1 +code 7 BUSY
= 4 as X1 +codes 6&7
= 5*as X4 +code 13 RINGING
= 6 as X1 +code 7&13 (no dialtone detect eg cellular)
Z p Make Configuration Profile p (0-3) the Active Profile
&B Character Length
= 0 8 Bit Characters
= 1 9 Bit Characters
= 2 10 Bit Characters
= 3 11 Bit Characters
= 4*Use Autobaud length (10 or 11 Bit)
&C DCD Signal
= 0 Always asserted
= 1*Asserted when carrier is valid
= 2 Always on except pulse low on disconnect
= 3 On throughout a voice connection
&D DTR Signal goes low
= 0*Ignored
= 1 Drop to online command mode if online
= 2 Hang up, auto answer off
= 3 Hang up, initialise modem to &Y stored defaults, auto answer off
= 4 Hang up, go off hook while DTR is low
&F = 0 Restore Factory Defaults
= 0 Restore LAP-M/MNP defaults except stored numbers, security & DES
= 1 Restore direct mode defaults except stored numbers, security & DES
= 2 Restore sync mode defaults except stored numbers, security & DES
= . Restore ALL Factory Defaults ( enter AT&F. )
= NOTE: %r %s %t %u are not reset by &F0,1 or 2
&G Guard Tones
= 0*Off
= 1 550Hz
= 2 1800Hz
&H Sync Clock Control
= 0*Clocks always present in sync mode
= 1 Clocks appear after connection
&K Flow Control
= 0 Off
= 3 RTS/CTS flow control
= 4 XON/XOFF flow control
= 5 Transparent XON/XOFF flow control
= 9*Auto CTS or XOFF (to DTE only)
&L Leased Line
= 0*Disabled (PSTN mode)
= 1 Enabled
= 2 Enabled Auto Originate
= 3 Enabled Auto Answer
&M Synchronous Mode
= 0*Async
= 1 Sync
= 2 Sync stored number dial
= 4 Async stored number dial
&N Abort Dial Character
= 0 Off
= 1*Abort dial with any character
&P Pulse Dial Ratio
= 0 39/61 (USA)
= 1*33/67 (Aust/NZ/UK)
&R Sync RTS/CTS Control
= 0*CTS follows RTS on-line, CTS high off-line
= 1 CTS always high
&S DSR Signal
= 0 Always asserted
= 1*Asserted during handshake
= 2 Asserted at end of handshake before CONNECT
&T Test Mode
= 0 Terminate
= 1 Local analog loopback
= 4*Grant RDL
= 5 Deny RDL
= 6 Remote digital loopback (RDL)
= 7 Remote digital loopback & self test
= 8 Local analog loopback & self test
&V View Configuration Profile
= No parameter Current Profile
= p Stored Profile p (0-3)
= 8 Current S registers different from default
&Wp Save Active Configuration Profile in Profile p (0-3)
&X Generate Sync Clocks
= 0*Modem
= 1 Terminal
= 2 Remote modem
&Yp Select Profile p (0-3) for Power-On and &D3
&Zn Store Phone Number eg AT&Z3=1234567
\A MNP Block Size
= 0 64
= 1 128
= 2 192
= 3*256
\Bn Send Break length n*100mS
\J MNP fallback to direct mode
= 0*Disabled
= 1 Enabled
\K Break Control (see manual)
\N Operating Mode
= 0 Constant Speed (buffered) mode
= 1 Variable Speed (direct) mode
= 2 MNP Reliable mode (MNP no fallback)
= 3*LAPM/MNP Auto-reliable mode (V.42 or MNP with fallback)
= 4 LAPM reliable mode (disconnect if not V.42)
= 5 LAPM Auto-reliable mode (fallback to constant speed or direct mode)
= 6 LAPM Auto-reliable mode (fallback to MNP Reliable mode if not V.42)
= 7 MNP Auto-reliable mode (fallback to constant speed or direct mode)
\Q Extended Flow Control
= None* &K selected disables \Q
= 0 Off
= 1 XON/XOFF flow control (&K4)
= 2 CTS flow control (from modem only)
= 3 RTS/CTS flow control (&K3)
= 4 XON/XOFF flow control (from modem only)
= 5 CTS flow control (CTS low until connection)
= 6 RTS/CTS flow control (CTS low until connection)
\S Display Current Profile with Explanation
\Tn Set Inactivity Timer n minutes
\V MNP Response Codes
= 0*Off
= 1 On
= 8 Extended
= 9 Extended+Diagnostic
\X XON/XOFF Pass Through
= 0*Off
= 1 On
#A Universal Remote Access
= 0 Off
= 1 On
= 2*Password protected
#B B0 and B2 1200bps originate mode
= 0*B0 = V.23, B2 = V.22
= 1 B0 = V.22, B2 = V.23
#C V.25 Calling tone
= 0 Off
= 1*On
#D V.25bis direct calling procedures
= 0*Off
= 1 On
#E DES Encryption
= 0*Off
= 1 On
#F Test Loops from Front Panel
= 0*Disabled
= 1 Enabled Sync Switch = Analog Loopback
= Orig Switch = Remote Digital Loopback
= Auto Answer Switch = Send Test Pattern
= Mode Led 1 = Test Pattern Indicator if Test Pattern is detected
#H or ? Display Help, may be followed by commands or a keyword
#I V.22bis Leased Line Mode
= 0*Normal
= 1 Use PSTN handshake with answer tone
#J V.42 protocol detect phase enable
= 0 Off
= 1*On
#K MNP 10 Adverse Channel Enhancements
Use with \N2 to ensure MNP only connection
= 0 Off
= 1*On
= 2 On with Cellular notification
#M V.25bis operating mode
= 0*Off AT command mode
= 1 Async V.25bis 7data+even parity
= 2 Sync V.25bis HDLC framing
= 3 Sync V.25bis character framing
#N V.25 sync encoding
= 0*NRZ format
= 1 NRZI format
#O Buffer Overflow Action
= 0*Characters ignored when buffer full
= 1 Disconnect if DTE (terminal) buffer fills
= 2 Disconnect if line buffer fills
= 3 Disconnect if either buffer fills
#Q V.25bis speed selection
= 0* Use last Autobaud speed
= 2-115 For complete list see R command
#R Remote Control On
Remote modem can issue commands to local modem after this command
Terminate remote access with ATO from either modem
#S Security Menu access
#U V.25 character set
= 0*ASCII
= 1 EBCDIC
#V Command Syntax Verify
= 0 Off
= 1*On
%C Compression Control
= 0 None
= 1 MNP5 enabled
= 2 V42bis enabled
= 3*V42bis with MNP5 fallback
%Dn Set Disconnect Delay to n seconds
%E Auto EQM Retrain
= 0 Off
= 1*On
= 2 V32 auto rate change
%F DTR/DSR override from front panel switches A & B
= 0 A & B switches control V.25bis function
= 1*Switch A forces DTR on, Switch B forces DSR high
%H MNP 10 Link Negotiation Speed
= 0*Use current B setting to set maximum speed, connect at this speed
= 1 Initial connection and handshake at V.22 (1200) upshift to b setting
= 2 Initial connection and handshake at V.32 (4800) upshift to b setting
= 3 Initial connection and handshake at V.32 (9600) upshift to b setting
= 9 Use current B setting for connection, NO initial upshift
%K CTS during Dial and Handshake
= 0*On
= 1 Off
%L View Receive Level or Set Transmit Level
= 0 Display current receive level (-dBm)
= 11-19 Set transmit level -11dBm to -19dBm
%M Mode LED function when on-line
= 0*Use mode LEDs to indicate connect speed
= 1 Use LEDS to indicate line status
= Mode 1 LED flashes when line quality is poor
= Mode 2 LED flashes on errors in received MNP/LAP-M frames
= Mode 3 LED comes on when flow control to DTE is asserted
%N Non-Standard Terminal speeds
= 0*Standard Baud rates
= 1 Standard to 14400 then 20800,31200,41600 and 62400
= 2 Standard to 38400 then 51200
%P DCD to CONNECT Message Timing
= 0*Connect message before DCD is asserted
= 1 Connect message after DCD is asserted
%Q Display current line quality (EQM) (0=perfect >10=poor)
%R CTS Override (only reset by &F.)
= 0*Off
= 1 CTS always follows RTS
= 2 V.25bis : CTS on when ready for command
%S DSR Override (only reset by &F.)
= 0*Off
= 1 DSR always follows DTR
%T DCD Override (only reset by &F.)
= 0*Off
= 1 DCD always ON
%U REL Message (only reset by &F.)
= 0*CONNECT/REL for MNP or V.42
= 1 CONNECT/LAP-M for V.42
= 2 CONNECT/LAP-M,REL-(2,4,10)/MNP-5,V.42bis/DES
%W Send welcome message to remote modem at connect
= 0*Off
= 1 On
*B Display current blacklisted and delayed numbers
*C Disable V.34 (use V.FC)
= 0*Off
= 1 On
*W Set welcome script for %W command |=newline
-Q MNP10 fallback to v22bis or v22
= 0*Enabled
= 1 Disabled
:E Compromise Equaliser in V.32/bis
= 0*Enabled
= 1 Disabled
***** FAX COMMANDS *****
CLASS 2 Commands:
+FAA Adaptive answer parameter
+FAXERR Fax error value
+FBOR Phase C data bit order
+FBUG HDLC Frame Reporting Control
+FBUF? Buffer size
+FCIG Report Remote ID (CIG)
+FCFR Prepare to Receive Prompt
+FCLASS Service Class Selection
+FCON Facsimile Connection
+FCR Capability to receive parameter
+FCSI Report Remote ID (CSI)
+FDCC DCE Facsimile Capabilities parameters
+FDCS Current Session Results parameters
+FDIS Current Session parameters
+FDR Data Reception Command
+FDT Data Transmission Command
+FDTC Report Remote capabilites (DTC)
+FET Post Page Message
+FHNG Call termination status parameter
+FHR Report received HDLC frame
+FHT Report transmitted HDLC frame
+FK Session Termination Command
+FSPL Enable Polling
+FLID Local facsimile ID (20 printable ASCII characters)
+FLPL Indicate document available for polling
+FMDL? Model ID
+FMFR? Manufacturers ID
+FMINSP Phase C minimum speed
+FNSC Non-Standard NSC Frame
+FNSF Non-Standard NSF Frame
+FNSS Non-Standard NSS Frame
+FPHCTO DTE phase C timeout parameter
+FPOLL Remote Polling Indication
+FPTS Page Transfer Status
+FREL Phase C received EOL alignment
+FREV? Code Revision
+FTSI Report Remote ID (TSI)
= VR,BR,WD,LN,DF,EC,BF,ST
VR (Vertical Resolution) = 0 Normal
=*1 Fine
BR (Bit Rate) = 0 2400bps
= 1 4800bps
= 2 7200bps
= 3 9600bps
= 4 12000bps
=*5 14400bps
WD (Page Width) =*0 1728 pixels in 215mm
LN (Page Length) = 0 A4 297mm
= 1 B4 364mm
=*2 Unlimited length
DF (Data Compression Format) = 0 1-D Modified Huffman
=*1 2-D Modified Read
EC (Error Correction Mode) =*0 disable ECM
BF (Binary File Transfer) =*0 disable BFT
ST (Scan Time/Line) VR=Normal VR=Fine
=*0 0ms 0ms
= 1 5ms 5ms
= 2 10ms 5ms
= 3 10ms 10ms
= 4 20ms 10ms
= 5 20ms 20ms
= 6 40ms 20ms
= 7 40ms 40ms
CLASS 1 Commands:
+FTS= Stop transmission and pause,
(10ms intervals 0-255)
+FRS= Wait for silence,
(10ms intervals 0-255)
+FTM= Transmit data with carrier
+FRM= Receive data with carrier
+FTH= Transmit HDLC data with carrier
+FRH= Receive HDLC data with carrier
B Set Modulation Standard and Autorange
Bn Originate Speed Answer Speed
300 1200 2400 9600 19.2k+
0 = V21 V23 V22b V32 Vfast-AUTO AUTO See also #B commands
1 = 103 212 V22b V32 Vfast-AUTO AUTO AUTO will connect to best V.34/V.
FC
2 = V21 V22 V22b V32 Vfast-AUTO AUTO ..V32b V32 V22b V22 V23 V21..
3 = V21 V21 ..Bell212A Bell103
4 = 103 103
5 = V23 V23
6 = V22 V22
7 = 212 212
8 = V22 V22b V22b V22b = V22bis
9 = AUTO
10 = V32 4.8k V32 4.8k
11 = V32b 7.2k V32b 7.2k
12 = V32U 9.6k V32U 9.6k V32U = Non-TCM V32
13 = V32 9.6k V32 9.6k
14 = V32 12k V32 12.0k
15 = V32b14.4k V32 14.4k
V.34 speeds: B setting limits maximum connect speed
Modem will automatically select highest useable speed on each connection
16 = 14.4k 17 = 16.8k 18 = 19.2k 19 = 21.6k 20 = 24.0k
21 = 26.4k 22 = 28.8k 27-31 sets 2.4k-12k V.34 speeds (AUTO)
Dial Modifiers may be embedded into phone number
eg ATDWT0,P123{at}T4567890
T Tone dial
P Pulse dial
W Wait for dial tone
R On-line in answer mode
, Pause
; Return to local command state
{at} Wait for quiet answer
! Hook flash
S=n Dial stored number n
A,B,C,D DTMF encoded character
#,* DTMF encoded character
F or ^ Inhibit calling tones
L Redial last number
J MNP 10 initial connection and handshake at V.22 1200
K MNP 10 cellular link notification
M MNP 10 initial connection and handshake at V.32 4800
Response Codes
= 0 OK 1 CONNECT
= 2 RING 3 NO CARRIER
= 4 ERROR 5 CONNECT 1200
= 6 NO DIALTONE 7 BUSY
= 8 NO ANSWER 10 CONNECT 2400
= 11 CONNECT 4800 12 CONNECT 9600
= 13 RINGING 20 CONNECT/REL
= 22 CONNECT 1200/REL 23 CONNECT 2400/REL
= 24 CONNECT 4800/REL 25 CONNECT 9600/REL
= 26 CONNECT 12000/REL 27 CONNECT 14400/REL
= 28 CONNECT 7200/REL 30 CONNECT 12000
= 31 CONNECT 14400 32 CONNECT 7200
= 33 CONNECT 16800 34 CONNECT 19200
= 35 CONNECT 21600 36 CONNECT 24000
= 37 CONNECT 26400 38 CONNECT 28800
= 62 CONNECT 115200
= 39 CONNECT 38400 40 CONNECT 57600
= 43 CONNECT 16800/REL 44 CONNECT 19200/REL
= 45 CONNECT 21600/REL 46 CONNECT 24000/REL
= 47 CONNECT 26400/REL 48 CONNECT 28800/REL
= 72 CONNECT 115200/REL
= 49 CONNECT 38400/REL 50 CONNECT 57600/REL
S Register Summary
Use ATSn? to read register, ATSn=x to set register
Reg Range Def Function
S0 0-255 02 Rings Before Answer
S1 0-255 00 Current Ring Count (read only)
S2 0-255 43 '+' Escape Sequence Char
S3 0-127 13 CR Carriage Return Char
S4 0-127 10 LF Linefeed Char
S5 0-127 08 BS Backspace Char
S6 4-7 04 Wait for Dial Tone - Secs
S7 1-60 30 Wait for Carrier - Secs
S8 1-7 04 Duration of PAUSE dial modifier - Secs
S9 1-255 06 Carrier Response Time - 100 ms
S10 1-255 18 Lost Carrier/Hang Up Delay - 100 ms
S11 70-254 95 DTMF Tone Spacing - msec
S12 3-255 50 Escape Sequence Guard Time - 20 ms
S16 0-8 0 Test in Progress (read only)
S18 0-255 00 Test Timer - Secs
S25 0-255 05 DTR Hi->Lo Steady Time - 10 ms
S26 0-255 00 RTS CTS Delay - 100 ms
S27 0-255 00 Delay Before Dial - Secs
S29 10-100 50 Hook Flash Duration - 10ms
S30 0-255 00 Data Inactivity Timer (non voice) - 10 Secs
S30 0-255 00 Voice-mode Dead-Man Timer - Secs ( = S105 )
S33 0-255 03 V32 EQM Retrain Value
S38 0-255 00 Disconnect Delay - Secs
S42 0-255 Modem Disconnect Reason (read only)
S43 0-255 15 Break Length - 20 ms
S45 0-255 98 V22bis EQM Retrain Value
S57 0-255 00 DTR Lo->Hi Steady Time - 10 ms
S62 0-255 75 V.42 detection phase timeout - 10 ms
S66 0-255 10 Remote Access Guard Time - 100 ms
S67 0-255 42 '*' Remote Access Character
S69 0-255 60 Command Line Timeout - Secs 0=off
S71 0-30 00 V.25bis time for command entry after ring - Secs
S74 0-255 00 Disconnect reason of call before last (read only)
S80 1-19 15 Flow control high water mark *5% (default: 75% of 1Kbyte)
S81 1-19 3 Flow control low water mark *5% (default: 15% of 1Kbyte)
S82 1-255 60 &K9 second flow control mark (characters past high mark)
S95 0-63 0 Extended result code bit map
S96 1-255 80 Columns per screen (used by &v for formatting)
S97 1-255 24 Rows per screen (used by help and &v for formatting)
S105 0-255 30 Voice-mode Dead-Man Timer
S42 disconnect reason codes
= 0 modem reset
= 1 user hang up by ATH
= 2 DTR dropped
= 3 Carrier lost
= 4 user switched to TALK mode
= 5 connection failed or timed out
= 6 no answer tone detected
= 7 connected at wrong speed
= 8 failed to connect within S7 time limit
= 9 buffer overflow (from line)
= 10 buffer overflow (from terminal)
= 11 sync MNP disabled
= 12 inactivity timer expired
= 13 unable to make MNP connection & fallback disabled
= 14 retrain failed
= 15 not used
= 16 aborted from keyboard during connection
= 17,18 MNP internal errors
= 19 Link Disconnect Frame received
= 20 MNP packet re-transmitted 12 times without response
= 21-26 MNP internal errors
= 27 analog loopback switch asserted while online
= 28 security system rejects user
= 29 V42/MNP not acheived, fallback prevented by DES
= 30 MNP10 rate fallback failed
= 31 CTS stuck in off state
= 32 Incoming call access denied
= 42 V42bis received invalid token
= 99 Invalid exit from online state
Compliance Test Tones +FTEST at+FTEST=n
Copyright (C) 1995 NetComm Ltd.
MNP is a registered trademark of Microcom, Inc.
OK
---------------------------------------------------------------------
Regards, Bill
@EOT:
--- MsgedSQ/2 3.30
* Origin: Logan City, SEQ (3:640/305.9)SEEN-BY: 640/305 711/934 @PATH: 711/934 |
|
| SOURCE: echomail via fidonet.ozzmosis.com | |
Email questions or comments to sysop@ipingthereforeiam.com
All parts of this website painstakingly hand-crafted in the U.S.A.!
IPTIA BBS/MUD/Terminal/Game Server List, © 2025 IPTIA Consulting™.