[Please note I'm having to post this directly from the os2hardware
Group-page due to the following problem! Also that:

   O:\DESKTOP]host 203.16.214.141
   203.16.214.141 = ipmail02.adl2.internode.on.net]

This is the response I received trying to send the below message which
I originated at Sun, 11 Mar 2007 04:42:14 +1000, which is 
Sat, 10 March 2007 18:42:14 +0000 (UTC date-time)

"This is an automatically generated Delivery Status Notification.

THIS IS A WARNING MESSAGE ONLY.

YOU DO NOT NEED TO RESEND YOUR MESSAGE.

Delivery to the following recipients has been delayed.

              

The reason for the problem:
4.1.0 - Unknown address error 451-'buzz y!groups blacklisted
203.16.214.141'



Final-Recipient: rfc822;os2hardware{at}yahoogroups.com
Action: delayed
Status: 4.0.0 (temporary failure)
Remote-MTA: dns; [66.218.66.71]
Diagnostic-Code: smtp; 4.1.0 - Unknown address error 451-'buzz
y!groups blacklisted 203.16.214.141' (delivery attempts: 4)
Reporting-MTA: dns; ipmail02.adl2.internode.on.net
Will-Retry-Until: 16 Mar 2007 05:12:16 +1030"


Subject:
Re: [OS2HW] Large IDE drive
From:
Mike O'Connor 
Date:
Sun, 11 Mar 2007 04:42:14 +1000
To:
os2hardware{at}yahoogroups.com

Andre Nancoz wrote:
> ** Reply to message from rallee2{at}comcast.net on Sat, 10 Mar 2007
04:16:47 +0000
>  
>> Within the bios setup utility there should be either under the
"Advanced"
>> section or in it's own "Peripherals" section (some older bioses
even had
>> "Chipset" for the most part, back when AMI, Phoenix, and
Award were
separate
>> and very different had a separate "autodetect ide drives" or
"peripherals"
>> section) there will be a list of the IDE controllers, Primary and
Secondary at
>> the least.  These will have options like either "Enable/Disable",
"Enable
>> Primary" "Enable Both" or something like that. 
There may also be a
line to
>> "enable/disable/auto" such pertinent items as DMA, LBA,
SMART and such.
> The BIOS has 4 lines for primary master slave, secondary master
slave. Each
> line has a list with  the options of "none, auto, user type HDD,
other ATAPI,
> CD-ROM, , MO, LS-120, ZIP-100". On "auto" the BIOS says
scanning for
device, up
> till now this always results in the result of "none" being
displayed. If I
> select "user HDD" I can then get a screen of options where I
can choose
> translation mode, PIO mode, Ultra-DMA mode, etc. When trying with
"user type
> HDD LBA mode the
> BIOS does not issue the scanning message and the display of
peripherals list the
> primary master as "none". The Dani driver does not seem to load, all
I get is a
> line with the version number and a line that says "SYS    : End of data
> DaniS506.ADD" .
>
> The "COPY IBMS506$ con:" as shown in the DANI doc just says:
>
>   There are no more files. "X:\Danis506\IBMS506$"
>
> For those who might understand, this is the output of the
dumpIDE.exe from the
> DANI package:
>
>     PCI BIOS V2.10 detected, 2 PCI buses reported.
>     PCI Bus scan: 2 PCI buses found.
>     Found legacy mode VIA 571 (1106/0571 rev 06) on 0:17.1
>     00:  06 11 71 05  00 00 90 02  06 8A 01 01  00 20 00 00
>     10:  00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00
>     20:  01 B8 00 00  00 00 00 00  00 00 00 00  00 00 00 00
>     30:  00 00 00 00  C0 00 00 00  00 00 00 00  00 01 00 00
>     40:  08 02 09 0A  1C 10 C0 00  A8 A8 A8 A8  FF 00 B6 B6
>     50:  07 07 07 07  0C 00 00 00  A8 A8 A8 A8  00 00 00 00
>     60:  00 02 00 00  00 00 00 00  00 02 00 00  00 00 00 00
>     70:  02 01 00 00  00 00 00 00  82 01 00 00  00 00 00 00
>     80:  00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00
>     90:  00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00
>     A0:  00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00
>     B0:  00 00 00 00  00 00 00 00  00 00 00 00  00 00 00 00
>     C0:  01 00 02 00  00 00 00 00  00 00 00 00  00 00 00 00
>     D0:  06 00 71 05  00 00 00 00  00 00 00 00  00 00 00 00
>     BusMaster Registers:
>     00:  FF FF FF FF  FF FF FF FF  FF FF FF FF  FF FF FF FF
>
>     VendorID 1106, DeviceID 0571
>     IOBase      B800h (Len 10h)
>     INTA -> IRQ0
>
>     South bridge (1106/3074 rev 00) on 0:17.0
>   
Hi Andre,

Noting above that you have an IRQ0(zero) showing up - which always
used to be associated with the System timers, try turning off
Plug'n'Play in the BIOS if that is currently set, and let the BIOS
allocate all the Boot-device IRQs.

HTH

Regards, 




------------------------ Yahoo! Groups Sponsor --------------------~--> 
See what's inside the new Yahoo! Groups email.
http://us.click.yahoo.com/0It09A/bOaOAA/yQLSAA/9rHolB/TM
--------------------------------------------------------------------~-> 

 
Yahoo! Groups Links

 To visit your group on the web, go to:
    http://groups.yahoo.com/group/os2hardware/

 Your email settings:
    Individual Email | Traditional

 To change settings online go to:
    http://groups.yahoo.com/group/os2hardware/join
    (Yahoo! ID required)

 To change settings via email:
    mailto:os2hardware-digest{at}yahoogroups.com 
    mailto:os2hardware-fullfeatured{at}yahoogroups.com

 To unsubscribe from this group, send an email to:
    os2hardware-unsubscribe{at}yahoogroups.com

 Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 

---