Excuse my tardiness in replying.  I must mention that an USR Courier 
modem is my primary modem with the ActionTec as the backup, which worked 
flawlessly last October with InJoy and Faxworks 3.00.01.

Kris Steenhaut wrote as follows on 07/02/06 19:05:

>Kenn Yuill wrote:
>  
>
>>>     As written previously on this or other lists, my internal
"Action 
>>> Tec Call Waiting PCI Modem" works fine with COM.SYS, ver. 1.2 and 
>>> Faxworks' driver, FMD.SYS.  It is identified as above and as a 
>>> "Lucent/Agere Venus WinModem" by PCI.EXE (PCI_VK).
>>>
>>>   
>>    
>>
>As is mine:
>
>  
>
>>> Vendor 11C1h Lucent/Agere Systems (Was: AT&T MicroElectronics)
>>> Device 044Ah LT WinModem 56k
>>> Command 0007h (I/O Access, Memory Access, BusMaster)
>>> Status 0290h (Has Capabilities List, Supports Back-To-Back Trans.,
>>    
>>
>Emulated to com2 IRQ9.
>  
>

    Mine uses COM 4, D800, IRQ 10.

>>>     Also, I got a handy utility from their web-site, PMDMCFG.EXE, which 
>>> scans for the modem and gives the port, i/o address & irq
in a DOS CL 
>>> session.
>>    
>>
>Does this tool do anything or does it just tell us about the emulated data?
>  
>

    I did use it on the previous Pentium 200MMX to set IRQ to 10, when 
this modem kept using an IRQ of 11 or 15, via the parameter, "/IRQ10".  
IIRC, it was necessary to specify IRQ 10 for its PCI slot in the 
mainboard's BIOS, so the IRQ wasn't shared.

>  
>
>>>   I don't know if this utility works for PCI modems with a 
>>> similar chipset from other manufacturers.  If anyone wants a copy of 
>>> this program to test its usefulness, let me know today so I
can send out 
>>> only *one* e-mail with attached archive to everyone.
>>>
>>>   
>>    
>>
>I really would like to hear how  to get Faxworks to work with my 
>emulated com2 irq9. All it sees at present is the real port 1 irq 4.
>  
>

    The applicable lines in my Config.Sys are

DEVICE=C:\OS2\BOOT\COM.SYS (1,3F8,4) (2,2F8,3) (4,D800,10)
DEVICE=E:\FAXWORKS\FMD.SYS (1,03F8,4) (2,02F8,3) (4,D800,10)

plus the following one was used with Ray Gwinn's 1.60d driver on my old box,
  REM DEVICE=C:\SIO\SIO.SYS (COM4:230400,D800,IRQ11)
which worked normally, AFAIR.

>Incidentally, this is a class 2 modem, isn't it?
>

    No, I have it set to Class 1 with HW FIFO, IIRC.

-- 
 Aloha,
         Kenn
 _____________________________________________________________________
        Always act as if life is a joyous journey. - Kenn Yuill
                __________ A Quote for Today __________
           All receive advice.  Only the wise profit from it.
                                      - Syrus
 _____________________________________________________________________
              * TagZilla 0.059 * http://tagzilla.mozdev.org>


 
Yahoo! Groups Links

 To visit your group on the web, go to:
    http://groups.yahoo.com/group/os2hardware/

 To unsubscribe from this group, send an email to:
    os2hardware-unsubscribe{at}yahoogroups.com

 Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 



---