Yo Pc-tech!
I recently upgraded my SFM 28.8 external (datapump 05BA) to beta -22 without 
any problems, except for the fact that 31k2 and 33k6 are slower than 28k8.
But I just had something strange happening: I tried to call to my ISP using 
the OS/2 Warp Internet Dialer (as I always do), but after the connect (a 
28.8/21.6) the PPP connection failed.
I redialed and I suddenly noticed that the supra "screen saver" (the one with 
DT/115) was activated. The modem dialed the number (I suppose). Then, in the 
log window, the following appeared:
06397:AA0000
06440:AA0100
The connect failed (NO CARRIER, because I don't have the speaker turned on, I 
don't know what the handshake sounded like). AT%q2 reported Carrier loss 
afterwards.
Here's some info about the modem:
ati2
OK
OK
ati3
V1.440-22-V34_DS
SupraFAXModem 288
Built: September 16 1996 16:12:24
OK
ati4
a007040CA879CE02F
bC60000000
r1005111151112004
r30001111FF100000
OK
ati9
($SUP1201\\MODEM\\SupraFAXModem 288B2)
OK
AT\s:
CMD DESCRIPTION / OPTION   CMD DESCRIPTION / OPTION   CMD DESCRIPTION / 
PTION
--- --------------------   --- --------------------   --- 
-------------------
    DTE BPS.........115K   -K  EXT. SERVICES......0   S0  RINGS TO 
NS.....000
    DTE PARITY.....8NONE   &C  DCD OPTION.........1   S1  RING 
OUNT.......000
    DIAL MODE.......TONE   &D  DTR OPTION.........2   S2   
HAR.......043
    RX LINE SPEED...NONE   &G  GUARD TONE......NONE   S3   
HAR........013
    TX LINE SPEED...NONE   &K  FLOW CONTROL.....RTS   S4   
HAR........010
B   BELL MODE.........NO   &P  PULSE MODE.........0   S5   
HAR........008
E   CMD ECHO.........YES   &Q  ASYNC/SYNC.........5   S7  CONNECT 
IME.....060
L   SPKR VOLUME......OFF   &R  RTS/CTS............0   S8  PAUSE 
IME.......002
M   SPKR CONTROL.......0   &S  DSR OPT............1   S11 DTMF 
URATION....095
N   AUTO MODE.........NO   &T  ENABLE RDL........NO   S12 ESC GUARD 
IME...050
Q   QUIET.............NO   &X  SYNC CLOCK.......INT   S18 TEST 
IME........000
V   RESULT FORM.....LONG   &Y  PROFILE........NVM.0   S24 SLEEP 
NACT......000
W   EC MSG.............2   \A  MAX BLK SIZE.....128   S30 CONNECT 
NACT....000
X   EXT RESULTS........4   \G  REMOTE FLOW.......NO   S36 FALLBACK 
CTION..007
Y   LONG SPACE DISC...NO   \K  BRK OPT............5   S48 V42 NEG 
TRL.....007
%C  COMPRESSION.....BOTH   \N  ECL MODE........AUTO   S86 FAILURE 
ODE.....004
%E  AUTO RETRAIN.....OFF   *H  NEG. SPEED......HIGH   S95 RES. 
DE........000
OK
AT\s1:
REG  DEC  HEX     REG  DEC  HEX     REG  DEC  HEX     REG  DEC  HEX
---  ---  ---     ---  ---  ---     ---  ---  ---     ---  ---  ---
S00  000  00H     S15  000  00H     S30  000  00H     S92  010  0AH
S01  000  00H     S16  000  00H     S31  200  C8H     S95  000  00H
S02  043  2BH     S17  000  00H     S32  017  11H     S109 067  43H
S03  013  0DH     S18  000  00H     S33  019  13H     S110 234  EAH
S04  010  0AH     S19  000  00H     S36  007  07H     S190 116  74H
S05  008  08H     S20  000  00H     S37  000  00H     S191 117  75H
S06  002  02H     S21  112  70H     S38  005  05H     S192 118  76H
S07  060  3CH     S22  112  70H     S39  003  03H     S193 116  74H
S08  002  02H     S23  062  3EH     S40  104  68H     S194 010  0AH
S09  012  0CH     S24  000  00H     S41  131  83H     S197 010  0AH
S10  014  0EH     S25  005  05H     S46  138  8AH     S200 004  04H
S11  095  5FH     S26  001  01H     S48  007  07H     S201 050  32H
S12  050  32H     S27  009  09H     S82  128  80H     S202 000  00H
S13  000  00H     S28  000  00H     S86  004  04H     S210 013  0DH
S14  138  8AH     S29  070  46H     S91  010  0AH
OK
AT&v:
ACTIVE PROFILE:
B0 E1 L0 M0 N0 Q0 T V1 W2 X4 Y0 %C3 %E0 %G1 -K0 &C1 &D2 &K3 &Q5 &R0 &S1 &X0 
&Y0
S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:060 S08:002 
S09:012
S10:014 S11:095 S12:050 S18:000 S23:062 S25:005 S26:001 S36:007 S37:000 
S38:005
S40:104 S41:131 S44:131 S46:138 S48:007 S91:010 S95:000 S109:067 S110:234
BTW: the above profile is from right after the "crashed call".
The init strings used by the dialer are:
ATI2E1Q0V1W2X4Y&C1&D2&K3
AT&Q5&R&S1&T5\\N3S7=60S37=0+esr=1
I'm using the SIO comm drivers version 1.55 with an UART 16550A and locking 
the port at 115200 bps (never had any problems with this).
Ahem, I just tried another dial, here's the result of "debug codes" (these 
were printed during the handshake, which of course failed): 
---
ATDT032161818
00156:AA0000
00210:AA0001
00211:AA0301
00333:AA0302 
00337:AA0402
00348:CE0502
00349:CE2002
00349:CE2020
00364:CE2120
00389:CE2122
00411:CE2123
00414:CE2223
00415:CE2827
00419:CE2828
00436:CE2829
B triggered
00452:CE282A
00457:CE282D
00462:CE282B
00465:CE292B
00466:CE2424
00483:CE2525
00501:CE252C
00501:CE2C2C
00535:CE4040
B triggered
00543:CE4041
00546:CE4046
00560:CE4047
B triggered
B triggered
00748:CE4048
00748:CE4448
00752:CE4548
00753:CE4648
00761:CE4748
B triggered
B triggered
00949:CE4860
EQM:0000
NP:01
00953:CE4861
00956:CE6263
00956:CE6363
B triggered
01083:CE6463
EQM sum:3303F3
ARA rate:00
01093:CE6465
B triggered
NO CARRIER
---
Meanwhile, the "screen saver is still active. I'm going to power cycle the 
modem. See next message for the rest.
Cya,
           Gamefreak 
--- FMail/2 1.20
---------------