Hi Don ... on 4 Mar 97 you wrote,
 DB> RC>bs> I should mention that I tried all three programs with all
 DB> RC>bs> combinations of "\J1", "S95=1,45,47" etc.  At no time was
 DB> RC>bs> S95 ever able to override the "W" setting and produce a DCE
 DB> RC>bs> value.
 DB>BS> Everything above is factory default except for "M0" ...  turned
 DB>BS> it off because of tinny noise from speaker :-(
 DB> Nothing wrong with those settings.  Odd however that you say that
 DB> use of the S95 register doesn't correctly reflect DCE speed.  The
 DB> AT&T chipset used in the Logicode fully supports S95 use.  In any
 DB> event the W2 setting will do for DCE reporting.  S95 merely expands
 DB> the reported facilities.
There is no complaint with any value that I give to S95 (ie 1,45,47,
etc.) ... it just has no effect :-))  You say that the Logicode is using
an AT&T chipset ... I was under the impression that it was a Cirrus
Logic chipset or are they one and the same?  My AT commands show:
 ATI1   CD04.08 - MM03.18P5 - Sp 03
 ATI3   CL - MD34xx
 DB> Reading your prior post where you say that CONNECT 31200 is
 DB> reported by the modem which however then in Telix changes to 1200
 DB> almost sounds as though Telix ( being somewhat old and prior to
 DB> 28/8/33.6 speeds ) does not recognise the 31200 as valid and
 DB> reverts to 1200.  And possibly also the same applies to Terminate (
 DB> incidentally not a program on my hit list).
I have tried Telix 3.22 as well as the latest 3.51 (May 96) and the Docs
make reference to 28.8 and 33.6 ... as for Terminate, I have talked to
others using ver 4.00 and Zoom 33.6 and have no problem displaying 28.8
and 33.6 DCE info.
 DB> Try forcing a lower speed connect via S37 register , say down to
 DB> 14400 which Telix will certainly recognise ..  S37=11 probably ...
 DB> and see if matters proceed OK.  Also use W2 and S95=0.  If all OK
 DB> then the software is at fault.
Great idea and I tried it.  I got my connect message showing 14,400 but
was unable to access data mode when I used W2, which is the same problem
as with S37 set to default of 0.  Tried various combinations of S95 and
all to no avail.  My BBS shows connect speed at logon time and also will
display USR stats if requested.  They show as 14,400/14,400 or with
S37=0, then 31,200/28,800.  So, forcing 14,400 made no difference
whatsoever ... I still can't display DCE speed :-((
 DB>BS> These are the settings for Terminate ver 4.00 but everything is
 DB>BS> identical to the above when I have used Telix 3.21 & 3.51.  I
 DB>BS> have also tried TTY and ANSI/BBS with no effect.
 DB> Nothing much wrong with these either.  One item which however has
 DB> no bearing on your problem is the FIFO buffer size setting.  8
 DB> would be preferable to guard against data overruns ..  14 leaves
 DB> only 2 bytes of headroom and thus marginal.  However if you have no
 DB> problems then leave as is.
Thanks for all your input.  Maybe if and when I get the 56k upgrade, it
will also fix this problem.  Compared with my USR Sportster 14.4 and
prior to that a Zoom 14.4, this modem is a dream!!!
Bye for now ... Bob
 * SLMR 2.1a *  
--- Maximus 3.01
---------------