AR>
MSGID: 1:107/101.0 371e2874
AR>Hayes Support wrote in a message to Alan Rackmill:
A
AR>OK
AR>**EMSI_REQA77E
AR>**EMSI_REQA77E
AR>Address 1:107/677@fidonet.org Using BinkleyTerm-OS/2 Ver. 2.60 
(UNREGISTERED)
AR>Welcome to The Nut House BBS !
AR>**EMSI_REQA77E
AR>Please press your Escape key to enter the BBS, or wait a few moments.
AR>**EMSI_REQA77E
AR>Please press your Escape key to enter the BBS, or wait a few moments.
AR>OK
AR>at&v1
AR>TERMINATION REASON.......... DTR LOSS
AR>LAST TX data rate........... 300 BPS
AR>HIGHEST TX data rate........ 300 BPS
AR>LAST RX data rate........... 300 BPS
AR>HIGHEST RX data rate........ 300 BPS
AR>Error correction PROTOCOL... NONE
AR>Data COMPRESSION............ NONE
AR>Line QUALITY................ 001
AR>Receive LEVEL............... 026
AR>Highest SPX Receive State... 00
AR>Highest SPX Transmit State.. 00
AR>EQM Sum Value............... 0000
AR>RBS Counter................. 0000
AR>OK
AR>ay&v
AR>at&v
AR>ACTIVE PROFILE:
AR>B1 E1 L3 M1 N1 Q0 T V1 W2 X4 Y0 &C1 &D2 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0 
Y0
AR>S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:050 S08:002 
S09:006
AR>S10:014 S11:095 S12:050 S18:000 S25:005 S26:001 S36:007 S37:000 S38:020 
S44:020
AR>S46:138 S48:007 S95:043
AR>STORED PROFILE 0:
AR>B1 E1 L3 M1 N1 Q0 T V1 W2 X4 Y0 &C1 &D2 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0
AR>S00:000 S02:043 S06:002 S07:050 S08:002 S09:006 S10:014 S11:095 S12:050 
S18:000
AR>S36:007 S37:000 S40:104 S41:195 S46:138 S95:043
AR>STORED PROFILE 1:
AR>B1 E1 L3 M1 N1 Q0 T V1 W2 X4 Y0 &C1 &D2 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0
AR>S00:000 S02:043 S06:002 S07:050 S08:002 S09:006 S10:014 S11:095 S12:050 
S18:000
AR>S36:007 S37:000 S40:104 S41:195 S46:138 S95:043
AR>TELEPHONE NUMBERS:
AR>0=                                     1=
AR>2=                                     3=
AR>OK
AR>Alan
AR>Team OS/2,
AR>Fidonet 1:107/101, ibmNET 40:4371/101, OS2NET 80:135/15
AR>
Alan,
   Let's try one more thing just to verify that that really is a 300
bit/s connect.  From terminal mode and the port set to at least
38,400 bit/s try issuing an
AT&FS95=60\V1
The modem should return "OK"
then dial via
ATDTn (where "n" is the number you are dialing)
and then let us know what connect messages you get (you should see the
connect, protocol, etc. messages there).
Also, when not connected, try issuing an ATi3 to the modem and let us
know what it returns.
   Also,  if it's convenient, you might try sending these results to
us at support@os.hayes.com.  It's much easier for us to deal with an
(Continued to next message)
--- FLAME v1.1
---------------