Hayes Support wrote in a message to Alan Rackmill:
AR>Hayes Support wrote in a message to Alan Rackmill:
AR>AR> HS>    I notice on the systems you are having problems
AR>AR> HS> connecting with you are getting a 'carrier 300' reported by
AR>AR> HS> the software.  This is obviously incorrect, and the only
AR>AR> HS> times I have seen software report that with a high speed
AR>AR> HS> connection is when the modem returned a carrier speed that
AR>AR> HS> the software was not configured to recognize, causing it to
AR>AR> HS> default down to 300.  You might try calling that system from
AR>AR> HS> terminal mode after issuing an AT&FS95=60 to the modem and
AR>AR> HS> see what the modem reports as a carrier speed.  Do you know
AR>AR> HS> what kind of modem is on the host system you are calling
AR>AR> HS> into?
AR> HS>
AR>AR>I have tried calling Hayes Optima v.34 and USR v.e modems that I know
AR>AR>for
AR> HS> sure.
AR> HS>
AR>AR>I don't know what others I have tried, but I have tried 9 different
AR>AR>BBSes
AR>AR>so
AR>AR>far, and only connect "properly" with one of them.
AR> HS>
AR>AR>I don't know what his modem is, but I have a message to him asking.
AR>AR>As soon as I find out, I will let you know.
AR> HS>
AR>AR>In the meantime, another problem that I have found is that often when
AR>AR>the
AR> HS> modem
AR>AR>I am calling answers the phone, my modem does not respond to that
AR>AR>modem's
AR>AR>"mating call" and it just sits there until the connect attempt times
AR>AR>out.
AR> HS>
AR>AR>I tried using the Smartcom program that comes with the modem and that
 HS> seems
AR> HS> to
AR>AR>work when the connecton is made.
AR>AR>But that will also just sit there sometimes.
AR> HS>
AR>AR>S95=60 does nothing.
AR>AR>I still get the same messages as above.
AR> HS>
AR>AR>Alan
AR> HS>
AR> HS>
AR> HS>
AR> HS> Alan,
AR> HS>
AR> HS>    After issuing an ATS95=60 to the modem from terminal mode
AR> HS> and manually calling into one of these systems that you are
AR> HS> having problems with (also manually, by typing ATDTn to the
AR> HS> modem where "n" is the number you are calling), what does
AR> HS> the modem report in the connect messages?
AR> HS> Michael -- Hayes Online Services
AR>According to the revised online guide, the max number for S95 is 43.
AR>However, I have tried both settings, and I get either a CONNECT or a
AR>CONNECT
AR>300 response.
AR>I will be doing some further "fiddling" later today and I will let you 
now
AR>what is going on.
AR>I will also include the AT&V1 readings after each attempt.
 HS> Alan,
 HS>    The modem should be reporting more than just a CONNECT
 HS> message, you should be getting the compression, protocol,
 HS> etc. responses as well. What terminal program are you using
 HS> and what is the port speed set for? 
 HS> Michael -- Hayes Online Services
I am using Binkley for OS/2.
Port is locked at 56700.
Here is the log for several calls made in terminal mode, and the results of 
at&v1 after each call.
I set S95=60 for all exceot the last one.
That one I set s95=43.
Als, I added my at&v results at the end.
************************
**EMSI_REQA77E
              
MAXIMUS/2 v2.02 
The Nut House BBS - Hayes Optima V.34 28800
Use Only REAL Names - Handles Will Be DELETED
NJ Bell Caller ID is no longer in USE !!!!!!!!
==============================================
What is your name?
NO CARRIER
at&v1
TERMINATION REASON.......... CARRIER LOSS
LAST TX data rate........... 300 BPS
HIGHEST TX data rate........ 300 BPS
LAST RX data rate........... 300 BPS
HIGHEST RX data rate........ 300 BPS
Error correction PROTOCOL... NONE
Data COMPRESSION............ NONE
Line QUALITY................ 127
Receive LEVEL............... 041
Highest SPX Receive State... 00
Highest SPX Transmit State.. 00
EQM Sum Value............... 0000
RBS Counter................. 0000
OK
NO CARRIER
at&v1
TERMINATION REASON.......... CARRIER LOSS
LAST TX data rate........... 300 BPS
HIGHEST TX data rate........ 300 BPS
LAST RX data rate........... 300 BPS
HIGHEST RX data rate........ 300 BPS
Error correction PROTOCOL... NONE
Data COMPRESSION............ NONE
Line QUALITY................ 127
Receive LEVEL............... 041
Highest SPX Receive State... 00
Highest SPX Transmit State.. 00
EQM Sum Value............... 0000
RBS Counter................. 0000
OK
ats95=43
OK
**EMSI_REQA77E
              
OK
at&v1
TERMINATION REASON.......... DTR LOSS
LAST TX data rate........... 300 BPS
HIGHEST TX data rate........ 300 BPS
LAST RX data rate........... 300 BPS
HIGHEST RX data rate........ 300 BPS
Error correction PROTOCOL... NONE
Data COMPRESSION............ NONE
Line QUALITY................ 001
Receive LEVEL............... 023
Highest SPX Receive State... 00
Highest SPX Transmit State.. 00
EQM Sum Value............... 0000
RBS Counter................. 0000
OK
**EMSI_REQA77E
              
**EMSI_REQA77E
Address 1:107/677@fidonet.org Using BinkleyTerm-OS/2 Ver. 2.60 (UNREGISTERED)
Welcome to The Nut House BBS !
**EMSI_REQA77E
Please press your Escape key to enter the BBS, or wait a few moments.
**EMSI_REQA77E
Please press your Escape key to enter the BBS, or wait a few moments.
OK
at&v1
TERMINATION REASON.......... DTR LOSS
LAST TX data rate........... 300 BPS
HIGHEST TX data rate........ 300 BPS
LAST RX data rate........... 300 BPS
HIGHEST RX data rate........ 300 BPS
Error correction PROTOCOL... NONE
Data COMPRESSION............ NONE
Line QUALITY................ 001
Receive LEVEL............... 026
Highest SPX Receive State... 00
Highest SPX Transmit State.. 00
EQM Sum Value............... 0000
RBS Counter................. 0000
OK
ay&v
at&v
ACTIVE PROFILE:
B1 E1 L3 M1 N1 Q0 T V1 W2 X4 Y0 &C1 &D2 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0 &Y0
S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:050 S08:002 
S09:006
S10:014 S11:095 S12:050 S18:000 S25:005 S26:001 S36:007 S37:000 S38:020 
S44:020
S46:138 S48:007 S95:043 
STORED PROFILE 0:
B1 E1 L3 M1 N1 Q0 T V1 W2 X4 Y0 &C1 &D2 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0 
S00:000 S02:043 S06:002 S07:050 S08:002 S09:006 S10:014 S11:095 S12:050 
S18:000
S36:007 S37:000 S40:104 S41:195 S46:138 S95:043 
STORED PROFILE 1:
B1 E1 L3 M1 N1 Q0 T V1 W2 X4 Y0 &C1 &D2 &G0 &J0 &K3 &Q5 &R1 &S0 &T5 &X0 
S00:000 S02:043 S06:002 S07:050 S08:002 S09:006 S10:014 S11:095 S12:050 
S18:000
S36:007 S37:000 S40:104 S41:195 S46:138 S95:043 
TELEPHONE NUMBERS:
0=                                     1=
2=                                     3=
OK
Alan
Team OS/2,
Fidonet 1:107/101, ibmNET 40:4371/101, OS2NET 80:135/15
internet: alanrack@ix.netcom.com
--- timEd/2 1.01
1:107/101)
---------------